Lighting Bulbs & Tubes

Share us

nd high reliability laser tube


origin: China


China .Long working hours and high reliability laser tube with High-Quality, Leading .Long working hours and high reliability laser tube Manufacturers & Suppliers, find .Long working hours and high reliability laser tube Factory & Exporters.

Mark & model :The product is featured as small size and good model, higher power rate compared with the laser tube of similar length It is forbidden to clean the mirror with acetone.The screws in the front and back ends of the laser tube are not allowed to be moved, otherwise the output power will be declined, even the tube will be scrapped.Put the acryl 300mm far away from output mirror, when testing its laser spot. JH1680 Main parameters Model JH1680 Length 1600mm Pipe Diameter 80±1mm Wavelength 10.6um Catalyst coated Yes Output Power Stable Value 140W Max Output Power 150W Triggering Voltage 26-28KV Working Voltage 20-23KV Triggering Current 4-5mA Max Working Current 30mA Type Of Cooling Water-cooling 15-25℃ Spot diameter 7±1mm Packing size 1800mmx160mmx150mm JH CO2 Laser Tube working life is up to 6000hours, The single tube power is up to 180W. The laser output is stable. The discharge tube is catalyst coated,the working life is much increased. Compared to similar product, the tube body length is shorter, the laser beam mode is better, the cutting speed is higher. JH CO2 laser tube 120W-160W small&medium power CO2 laser tube mainly used for laser engraving and laser cutting, applies to the vast majority of domestic co2 laser cutting machine, laser engraving machine, laser carving machine and laser marking machine. 1) In order to fully circulate the cooling water of the laser tube, it is necessary to ensure that the water flow enters from the low point and drain away from the high point under the pressure of the water so as to achieve the cooling of the entire laser tube. 2) If the flow direction is opposite, it is possible that the cooling water can not fill the whole pipe,resulting in poor cooling,power reduction and the phenomenon of tube burst. 3)If there is air bubbles in the laser tube,before the dimming,lift the water outlet side,until the bubble is completely discharged, and then fixed laser tube,please be careful not to allow residual bubbles in the laser tube.On the one hand, it will affect the light effect, on the other hand, it will lose the laser power. If the laser tube is poor cooling caused by bubble for long time, it may burst. Model Specification(mm) Rated power Max power Warranty(month) JH600 600×50 30W 40W 3 JH700 700×50 40W 50W 3 JH800 800×50 40W 50W 3 JH1000 1000×50 50W 80W 3 JH1080 1000×80 60W 90W 3 JH1260 1200×60 60W 90W 3 JH1280 1200×80 80W 110W 6 JH1480 1400×80 100W 130W 6 JH1680 1600×80 130W 150W 6 JH1660 1600×60 80W 130W 6 JH1880 1800×80 150W 180W 6 JH Laser Tube Operation Instruction 1. Installation Requirement Make sure to follow the operation instruction of JH Laser Tube as shown in the illustration. The dedicated power P14 should be equipped. The positive pole of laser tube is in high voltage (the ignition voltage is 24kv). It may cause the following consequence when it is failed to follow the instruction: Arcing; the inner tube will be punctured by electricity and may cause water leakage. 2. Operation conditions Water cooling: using purified water; 3 to 5 liter/minute; water temperature: 10℃-40℃. The operating environment: temperature 2-40℃; humidity 10-60%. The working current: test current is 30mA. Maximum working current is 30mA. The running current must be kept below 28mA. The life span can reach 10,000 hours if the current is kept below 26mA. The ammeter must be connected to the negative electrode of laser tube. When it is working under over-high current for long term, the negative pole will appear brown yellow, and the life span will be shortened rapidly. To protect dust from going into the insulation sheath, please wrap it with plastic film. 3. Working Performance Cutting function. Engraving function: Very good. When the working current is 4mA and the tube is in the state of preionization, the laser can be used for high-frequency impulse engraving. 4. Key Notes Do not clean the exterior surface of the output widow mirror with tools such as tampon; otherwise the output power will be seriously affected. The followings are the designated methods to clean up pollution in the exterior surface of window mirror: 1) When the mirror is polluted, do not turn on the laser. 2) Blow the mirror surface sideways with an air blower. 3) Spray the pure alcohol on the mirror surface with sprayer. 4) Turn on the laser after the alcohol gets fully volatilized. 5) If the methods above don't work effectively, it is necessary to ask for the professional to use tampon with alcohol to clean the mirror surface from middle to edge. The best solution is to prevent the window from being polluted. Attention: it is forbidden to clean the mirror with acetone. The screws in the front and back ends of the laser tube are not allowed to be moved, otherwise the out power will be declined, even the tube will be scrapped. Put the acryl 300mm far away from output mirror, when testing its laser spot. 5. Safety The laser beam is invisible light. Please wear protective glasses when debugging the laser. The positive pole is in high voltage. Pay attention to the security marks. 6. Storage and Transportation Requirement Pour out cooling fluid in the event of storage and transportation, and cover the output terminal with a dust-proof plastic bag. The storage environment is 2-40℃, and the requested humidity is 10-60%. Pack the laser as in the original way. important notes: it is requested to use adhesive tape to cement the sponge together with laser tube to prevent the tube from vertically sliding during transportation. The sponge in the side of output mirror must be 70 mm beyond it, and the sponge in the side of reflecting mirror must be 50 mm wider. Tubes operated in wrong way are not guaranteed by Manufacturer.

Suitable for Desktop Laser 50w, Co2 Laser Cutting Engraving Machine, Sealed Metal Co2 Glass Tube,

Read More


60w 80w CO2 laser power supply...

ShiJiaZhuang Jing Hang Laser Technology Co., LTD.

South korea,Brazil,France,Germany

Read More


Tel: 13803363361
gaoyi, Hebei, China,


H5/响应式/营销型企业网站; 26种语言扩展;
覆盖: 英文、法语、德语、西班牙语、葡萄牙语、俄语、阿拉伯语、波斯语、日语、韩语